Quickstage Microscope Stage Chambers

Quickstage Microscope Stage Chambers

FEATURES

  • Heated and unheated perfusion chambers
  • Extensive range of chamber designs
  • Wide microscope stage compatibility
  • Environmentally controlled version
  • Optional tool tray and manipulators

Description

DESCRIPTION

Automate Scientific QuickStage microscope stage adapters and heated or unheated perfusion chambers are designed to fit directly into your Olympus, Nikon, Zeiss (K & M), Leica, Siskiyou, Scientifica, Narishige, Thor Labs, or Sutter microscope stage or platform. With a simple twist of two locking nuts, the entire stainless magnetic Tool Tray lifts off with all of your magnetic tools still attached. The underlying chamber and coverslip are then free for easy cleaning and replacement. Optical #1 thickness cover slips provide a perfect imaging surface for upright or inverted microscopy.

  • Integrated spill channel
  • Magnetic stainless steel tool platform
  • For Nikon, Olympus, Zeiss and Leica upright & inverted microscopes

The heated version of the QuickStage uses AutoMate Scientific’s popular ThermoClamp temperature controller to maintain your set temperature from ambient to 50°C. Disassembly and cleaning of the heated chamber is just as simple as the unheated version. The ferro-stainless Tool Tray can be removed with all of your tubes and electrodes intact. A silicone gasket ensures leak-free performance without messy grease. Stage heating is maintained while coverslips are replaced so you can begin recording again sooner.

Part Numbers

QuickStage part numbers look complicated, but they are actually pretty easy. Refer to the chart below:-

 


Heated Perfusion Chambers

Unheated Perfusion Chambers

Unheated perfusion chambers: horizontal, round, and vertical (QS-U-H, -V & -R) These use 22 mm square #1 coverslips on the bottom, and accept 13 mm round coverslips on top. Small magnets and clips hold your pipes. These work with any of our stage adapters.

Microscope Stage Adaptors

Retainers

Tool Trays are ferro-magnetic stainless steel plates designed to hold your perfusion chamber down to the stage adapter while also providing a large surface for StageHandsTM magnetic tool holders. Round stage adapters (i.e. Olympus and Nikon) include a square Tool Tray (4.25 in / 10.8 cm wide x 4.56 / 11.6 cm deep). Rectangular stage adapters (i.e. Zeiss and Universal) include a rectangular Tool Tray (5 in. / 12.7 cm x 3.5 in / 8.9 cm deep).

If you don’t have room on your stage for a Tool Tray, or think it is too large, you can order your QuickStage with Clamps instead. They hold the perfusion chamber down to the stage adapter using the same two thumb nuts on each side. For heated cell chambers (not unheated chambers or 35 mm dish holders), Clamps also require four small screws to hold the chamber, gasket and coverslip to the heating adapter.

Microscope Selection Chart

Heated Environmental Lid for 35mm dishes

Heated glass lid with perfusion and gas control attaches magnetically to the top of our 35mm dish holders. Control the temperature of a large 30 mm coverslip lid to minimize condensation while maintaining gas and temperature control over your 35mm dish. Separate perfusion inflow, aspiration outflow, gas connection, temperature sensor and grounding provided.

 

Dual-channel ThermoClamp®-2 Temperature Controller

Two independent channels for simultaneous heating of Environmental Lid or Perfusion Pencil® inline heater and heated QuickStage.

Dual Channel Thermoclamp

35mm Petri Dish Holders and Heaters

Unheated 35mm Petri dish holder (QS-U-35) with Nunc adapter ring. Rotating spring clips hold your dish securely for long-term imaging. This adapter also holds full- size slides. Shown with Tool Tray on Zeiss “M” stage adapter.

Adapters available for Nunc, WillCo, Falcon, In Vitro (D35-10-1-N), Corning, Mattek, and In Vitro (D29-10-1-N) 35mm dishes.  A heated 35mm Petri dish holder (QS-H-35) with spring clips and Corning adapter ring if also available with integrated temperature sensor (see below).

StageHands™ Magnetic Tool Holders

Magnetic base, arms, manifold and tube holders mount everything securely on your microscope stage for electrophysiology and perfusion. The magnetic base of these different StageHands are de
signed to stick tightly to a steel ring around your perfusion chamber like the QuickStage™, or any steel surface nearby.
StageHands™ Magnetic Tool Holders

They include a 1⁄4-20 screw to insert into a non-magnetic platform or air table.   Footprint: 0.75″ (19 mm), adjustable in all axes, extends to over 4.5″ (12 cm) long. Can be used to hold electrodes, tubes, manifolds, temperature sensors, glass capilliaries, agar bridges, etc. Thumbscrews allow easy adjustment without needing any tools. All stainless steel and anodized aluminum parts so they won’t oxidize or corrode.

Start with the StageHands Kit #1 (U.SH-1 shown, tool tray not included) which comes with two magnetic bases with a pair of 1.5″ (4 cm) arms, one locking ball joint, both a single and double tube/ electrode holder, plus a separate manifold holder. Add more arms, holders or bases as desired.

Read more

DOWNLOAD BROCHURE

Digitimer-Life-Science-Brochure-1

GET SUPPORT







Consent to being contacted via:
EmailPhone
By submitting, you are subject to terms and conditions of our privacy policy.